series am6cw-nz 6 watt | dc-dc converter www.aimtec.com tel: +1 514 620 2722 toll free: + 1 888 9 aimtec (924 6832) f 051e r13 1 of 3 north america only picture coming soon features: ? wide 4:1 input voltage range ? ? high efficiency up to 85% ? ? 1500 vdc isolation ? ? low ripple & noise models single output model input voltage (v) output voltage (v) output current max (ma) isolation (vdc) max capacitive load(uf) efficiency (%) AM6CW-11005S-NZ 40-160 5 1200 1500 1000 81 am6cw-11012s-nz 40-160 12 500 1500 100 83 am6cw-11015s-nz 40-160 15 400 1500 100 85 am6cw-11024s-nz 40-160 24 250 1500 47 85 note: all specifications in this datasheet are measured at an ambient temperature of 25c, humidity<75%, nominal input voltage and at rated output load unless otherwise specified. input specifications parameters nominal typical maximum units voltage range 110 40-160 vdc filter pi absolute maximum rating (100ms) 110 180 vdc no load input current 2 ma input reflected current 20 ma isolation specifications parameters conditions typical maximum units tested i/o voltage 60 sec, <1ma 1500 vdc resistance 500vdc >1000 mohm capacitance 1000 pf output specifications parameters conditions typical maximum units voltage accuracy 2 % over voltage protection 110-140 % of vo short circuit protection continuous short circuit restart auto-recovery line voltage regulation full load, ll to hl 0.5 % of vin load voltage regulation 5% to 100% load 1 % temperature coefficient 100% load 0.03 %/ o c ripple 25 mv p-p noise 100 mv p-p transient recovery time 25% load step change 1 ms transient recovery deviation 25% load step change 5 % general specifications parameters conditions typical maximum units switching frequency 100% load 300 khz operating temperature derating above 71c -40 to +85 o c storage temperature -55 to +125 o c maximum case temperature 100 o c cooling free air convection
series am6cw-nz 6 watt | dc-dc converter www.aimtec.com tel: +1 514 620 2722 toll free: + 1 888 9 aimtec (924 6832) f 051e r13 2 of 3 north america only general specifications (continued) parameters conditions typical maximum units humidity 95 % rh case material aluminum alloy weight 14 g dimensions (l x w x h) 1 x 1 x 0.46 inches 25.40 x 25.40 x 11.70 mm mtbf >1,000,000 hours (mil-hdbk -217f, ground benign, t=+25 o c) maximum soldering temperature 1.5mm from case for 10 sec 300 o c vibrations 5-150hz, displacement: 7.5mm, acceleration: 2g safety specifications parameters standards meets en60950-1 en 55022, class b (with the recommended emc circuit) pin out specifications pin single 1 -vin 2 +vin 3 +vout 4 -vout dimensions notes: ? all dimensions are typica l in millimeters (inches). ? case tolerance 0.25 (0.01) pin diameter tolerance 0.1 (0.004) pin height tolerance 0.5 (0.02) 25.40 (1.00) 2.54 (0.10) 20 .32 (0.80) 2.54 (0.10) 10 .16 (0.40) 5.08 (0.20) 20 .32 (0.80) 25.40 (1.00) 9.90 (0.39) printed face 1.00 (0.39) top view side view 2.54 (0.10) 1 +v input 2 -v input 3 4 +v output -v output bottom view
series am6cw-nz 6 watt | dc-dc converter www.aimtec.com tel: +1 514 620 2722 toll free: + 1 888 9 aimtec (924 6832) f 051e r13 3 of 3 north america only derating -40 -20 0204060 80 100 100 80 60 40 20 0 safe operating area output power (%) 85 ambient temperature o c free air convection 71 o c recommended emc circuit am6cw \ nz ????? ??????? l1 ???????? 10mh ???????? l1 ?????????? 10mh +vin ?????\ vin +vo ????\ vo ?????? cx ???????? 0.68uf ?????? cx ???????? 0.68uf ?????? cx ???????? 0.68uf 1nf/2kv y2 1nf/2kv ???? ????? y1 note: 1. datasheets are updated as needed and as such, specifications ar e subject to change without notic e. once printed or downloaded , datasheets are no longer controlled by aimtec; refer to www.aimtec.com for the most current product specifications. 2. product labels shown, including safety agency cert ifications on labels, may vary based on the date manufactured. 3. mechanical drawings and specifications are for reference only. 4 . all specifications are measured at an am bient temperature of 25c, humidity<75%, nominal input voltage and at rated output load unless otherwise specifie d. 5 . aimtec may not have conducted de structive testing or chemical anal ysis on all internal components and chemicals at the time of publishing this document. cas numbers and other limited information are considered proprietary an d may not be available for release. 6. this product is not designed for use in critical life support systems, equipment used in hazardous environments, nuclear control sys tems or other such applications which necessitate specific safety and regulatory standards other the ones listed in this datasheet . 7. warranty is in accordance with aimtec?s st andard terms of sale available at www.aimtec.com .
|
